How do I use Bathroom & Shower Cleaner?Updated 23 minutes ago
TL;DR: Bathroom & Shower Cleaner is ready to use, not a concentrate. Decant it straight into Foaming Spray Bottle via the tap at the base of the refill box, as it comes, filling to just below the shoulder so the pump has an air gap to work with. No water, no measuring, no mixing it with anything else. For a light clean, lay down two foam lines in a criss-cross across the surface. For heavy build-up, add two diagonals to make a star. Let it sit 2 to 10 minutes depending on how bad it is, then wipe and rinse. One box refills the bottle six times.
Is Bathroom & Shower Cleaner a concentrate?
⚠ Ready to use, so do not water it down
There is no dilution ratio to get right, because there is no dilution. The formula is built to work at the strength it leaves the box at, and every splash of water you add takes it further from that.
The same goes for topping the bottle up with another product. Mixing cleaners is how you end up with something that foams less, cleans less and behaves in a way nobody has tested. One product, one bottle.
How do I fill the Foaming Spray Bottle?
✓ Fill it in three steps
Open the tap, open the bottle. Unscrew the foaming head and pull the tap at the base of the refill box forward. Hold the bottle, not the box, while you fill.
Decant to the fill line. Leave a small air gap at the top. A foaming pump needs air as well as liquid, so a bottle filled to the brim will spit rather than foam.
Screw the head back on firmly. Give the pump a couple of primes and it's ready.
Refills per box
Six
One box fills Foaming Spray Bottle six times.
The foaming pump bottle Bathroom & Shower Cleaner is designed to go in. Refill it from the box rather than replacing it, and grab a spare when the pump eventually wears out.
⚠ If the bottle stops foaming properly
Dried product can build up in the nozzle after a stretch without use.
Submerge the head in warm water and pump it 12 times to clear it. Rinse the bottle out with warm water before a refill and it rarely happens at all.
How much foam should I spray?
✓ Light to moderate clean
Two foam lines in a criss-cross. One horizontal across the surface, one vertical. Spread it out with the block colour side of dampened Ultra Pro Bathroom Mitt, let it sit, then wipe and rinse.
✓ Heavy build-up
Add two diagonal lines so the pattern makes a star. More coverage, longer time on the surface, then the striped scrubby side of dampened Ultra Pro Bathroom Mitt for anything still holding on.
⚠ More foam is not more clean
Emptying half the bottle onto a shower screen does not shift grime faster. It just means a longer rinse and a box that runs out sooner. What actually moves the needle is even coverage and time on the surface, which is why the criss-cross exists.
How long should the foam sit before I rinse?
Weekly maintenance
2 to 3 minutes
Criss-cross, spread, wait, rinse. No scrubbing required.
Moderate soap scum
Around 5 minutes
Criss-cross, spread, wait, then a light pass with the striped side.
Heavy build-up
Up to 10 minutes
Star pattern, re-spray if it starts to dry, then scrub and rinse well.
✓ Finish with a rinse, every time
This is a foam and rinse product. Rinse the surface down with water after wiping rather than buffing the foam off dry, or you will see streaking on glass and a film on tiles. Drying glass afterwards is what gets you the streak-free finish.
Good Environmental Choice Australia (GECA) certified, Sensitive Choice approved, Dermatest tested, Eczema Association of Australasia recognised. Made in Australia.
Bathroom & Shower Cleaner, Ultra Pro Bathroom Mitt and Foaming Spray Bottle. New to Koh, this is the one to start on.
Koh Perks · earn points on every order
Earn points on every purchase, refer a friend, and redeem for discounts on your next order.
Browse all Bathroom & Shower Cleaner articles
Last reviewed: October 2026 · Koh Australia